Over the years there have been so many inventions. They include vehicles, bicycles and motor cycles. Motorbikes have become common worldwide and have so many uses. Some use them as a means of transportation while to others riding them is just a recreational activity. The fact that they are often used they need to be serviced regularly. The article points out how to install Harley risers, on your own.
You have the option of visiting the auto body shop and having a for you. On the other hand, you can choose to perform the exercise it yourself which will in turn save you a lot of money. But it is mandatory you know what is supposed to be done. You need shop rags, a handlebar riser kit, a ratchet, a blue Loctite, a plug set and a half inch torque wrench.
The shop rags are for covering your fuel tank as you work. This is because the fuel tank is very close to the handle bars. It may get scratched by the tools or even a handle bar and will cost you a whole new paint job. As interesting as the paint job sounds, it tends to cost a lot of money, and no one likes throwing money around.
Secondly, you may locate the triple clamp and position the riser stand inside it. Introduce the riser fair below the triple clamps. You should ensure that all these pieces are properly sealed together to ensure that you do not set yourself in any form of risk. This is necessary because if you ride a faulty motorbike, you may even suffer fatalities.
Ensure that you place a locker nut into each riser bolt and begin to start tightening them. Continue to apply blue Loctite, you should ensure the safety of your new setup by tightening the bolts and nuts using the ratchet and the socket. This is mandatory in ensuring that you are safe as you are using the motorbike and it is also not a danger to others.
Now to install the handlebars, align the bolt holes with the holes in the riser. Fit the bolts through the holes. At this point your ratchet and socket should help you tighten these bolts as tight as you can. If you do not ensure the that the bolts are tightened right, you might face danger the future. This means the handle bars may fall off while you are on the road.
Use the torque wrench to ensure all the nuts are in place in order to avoid the unnecessary inconveniences. These wrenches are made differently for each motor bike. It is upon you to follow the manufactures instructions to find out which wrench is best for your made bike. This information can also be acquired from a professional in an auto body shop.
As soon as you are able to handle the change the handle bars, you can do much smaller jobs on your bike like changing the light whenever it is defective. You can go and try out your new handle bars on the road.
You have the option of visiting the auto body shop and having a for you. On the other hand, you can choose to perform the exercise it yourself which will in turn save you a lot of money. But it is mandatory you know what is supposed to be done. You need shop rags, a handlebar riser kit, a ratchet, a blue Loctite, a plug set and a half inch torque wrench.
The shop rags are for covering your fuel tank as you work. This is because the fuel tank is very close to the handle bars. It may get scratched by the tools or even a handle bar and will cost you a whole new paint job. As interesting as the paint job sounds, it tends to cost a lot of money, and no one likes throwing money around.
Secondly, you may locate the triple clamp and position the riser stand inside it. Introduce the riser fair below the triple clamps. You should ensure that all these pieces are properly sealed together to ensure that you do not set yourself in any form of risk. This is necessary because if you ride a faulty motorbike, you may even suffer fatalities.
Ensure that you place a locker nut into each riser bolt and begin to start tightening them. Continue to apply blue Loctite, you should ensure the safety of your new setup by tightening the bolts and nuts using the ratchet and the socket. This is mandatory in ensuring that you are safe as you are using the motorbike and it is also not a danger to others.
Now to install the handlebars, align the bolt holes with the holes in the riser. Fit the bolts through the holes. At this point your ratchet and socket should help you tighten these bolts as tight as you can. If you do not ensure the that the bolts are tightened right, you might face danger the future. This means the handle bars may fall off while you are on the road.
Use the torque wrench to ensure all the nuts are in place in order to avoid the unnecessary inconveniences. These wrenches are made differently for each motor bike. It is upon you to follow the manufactures instructions to find out which wrench is best for your made bike. This information can also be acquired from a professional in an auto body shop.
As soon as you are able to handle the change the handle bars, you can do much smaller jobs on your bike like changing the light whenever it is defective. You can go and try out your new handle bars on the road.
About the Author:
When you are searching for information about Harley risers, visit our web pages online today. More details are available at http://www.demonscycle.com now.
No comments:
Post a Comment